Find localhost ip mac3/9/2024 Your MAC address will be listed next to a field labeled Physical address (MAC).On the Status page, choose View your network properties at the bottom of the Change your network settings menu.The document root for your apache server, by default, is 'Sites' in your home directory. Select Network and Internet from the Windows settings menu. Theres no such thing as a 'localhost' folder the word 'localhost' is an alias for your local computer.On Windows 10, select Start (Microsoft icon) and then choose Settings (gear icon) from the left-hand menu. Alternatively, when running ipconfig /all, the MAC address you are looking for is located under Ethernet adapter Ethernet: Physical Address. To find your MAC address and local IP on an iPhone or iPad, open up the Settings app, tap 'Wi-Fi,' then tap the 'i' button next to your Wi-Fi network. If Ethernet is the only connection to your computer at the time you run getmac, then the physical address whose Transport Name isn't media disconnected is the MAC address you are looking for. In the command prompt window, you can type either getmac or ipconfig /all.Open command prompt either by searching for it using the search bar in your menu or by doing the following key combination, typing cmd, and hitting enter: Windows Key + R.Select Hardware from the centered menu of the page. Your MAC address will be listed next to a field labeled with the same name.Select the Advanced button corresponding to the Built-in Ethernet or Network Adapter (depending on how you access the network).Select Network from the System Preferences panel.Select System Preferences from the Apple menu located on the top left-hand corner.If your Linux OS does not have the ifconfig command, you may also use the ip addr command.The MAC address will be listed next to HWaddr. Open a terminal and use the ifconfig command.Instructions to properly identify the MAC address for each corresponding Operating System is listed below: Letters must also be capitalized on the form. Please always include the colons ( :'s) between the numbers. Public: Go to and search for what is my IP address to find your public IP address. On Windows it will sometimes be represented with dashes between the numbers. The physical (MAC) address is an 8 byte number such as 08:00:20:9A:38:34. For that reason, the MAC address of a machine is required so that it can be properly configured for the engineering network. The MAC address is used to assign the TCP/IP address by means of DHCP (Dynamic Host Configuration Protcol). This is the actual hardware address that the lowest level of the network uses to communicate. Is that correct? or do I also need to add the sharename to the end of that? As I did not get any improved results.Every network interface has a MAC address (Media Access Controller) also known as the physical address. # prevent Apache from glomming onto all bound IP addresses (0.0.0.0) # Change this to Listen on specific IP addresses as shown below to I added my pc’s ip address to the following lines in Apache’s nf: # Listen: Allows you to bind Apache to specific IP addresses and/or So, I can only assume that I will need to tweak Apache (as you mentioned). html” and saved it to that directory and when I browsed to it again, I was able to see index.html rendered correctly. When I browsed to that folder (from the pc, in a browser), I was shown the directory itself (files and folders) but, I created a file, “index. OK, I tested browsing to the directory on my mac (from the pc). In which case, you will need to tweak the apache setup to listen on other addresses. Wwb_99: Unless the mac is not properly configured to accept http connections from outside of localhost, that is. Unless the mac is not properly configured to accept http connections from outside of localhost, that is. The best way to do this is to explicitly state “Hey, windows, this is a http connection!” by typing in your windows browser. What you need to do is open a http connection. You are connecting to a file share using \\192.168.0.5\ShareName. So, basically, I wanted to be able to open up the site to test it from the pc, without always having to upload my modified files to my sites remote server for testing. If I was to browse to those files (.php) across the network from the pc, and tried to open one of them, then it would open them with dreamweaver, or my pc’s default app. On the mac, I have all my files (for Apache localhost) in a folder, and have set up a doc root in nf, so, when on the mac, I open up and it shows me the site that I am testing locally. Hi… yeah, I already have the mac connected across the network, and have used its ip address to establish the connection (192.168.0.5).
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |